Dating south bend lathe japan dating sites reviews

Rated 3.86/5 based on 931 customer reviews

0 boring head; a special dial-test indicator marked BCA; the maker's original tool kit with spindle-bearing adjustment spanners; a drill chuck, Lo-Vo light unit and a good selection of clamping tools. £1450 Phone: 01303-627866 or email: [email protected](situated in Sandgate near Folkestone, Kent). A versatile, heavy-duty lathe in full working - but reasonably priced, as we need the room.Pictures of the BCA jig borer for sale here and details of BCA jig borers here, a Burnerd 3-jaw chuck 4-way toolpost, a proper Low-Vo light unit, tailstock chuck, metric thread-dial indicator, coolant system and a set of anti-vibration pads for the stand mounting. £1550 Phone: 07511-842648 Pictures of the Colchester Master 2500 for sale here and details of Colchester Master 2500 lathes here that gives a very wide speed range with eight in total from 82 to 2900 r.p.m.3-phase electrics so ideal for conversion to variable-speed inverter drive in which case the bottom speed might go as low as 10 r.p.m and the top to over 4000 r.p.m. £475 Pictures of the Boxford drill for sale here and details of Boxford drills here. £475 Pictures of the Startrite bandsaw for sale here Phone: 02086-395264 or email: [email protected] (Langley Park School, Beckenham).Phone: 02086-395264 or email: [email protected] (Langley Park School, Beckenham)- your choice of either a unit which requires fitting to a larger LEV system or a unit with extraction motor at the back of the LEV booth. These are compact, modern machines that have had school use only and both are in very similar condition.

dating south bend lathe-68

£1700 Phone: 0747-1182510 after 2 pm please and ask for Graeme.Details of these Harrison lathes and their development here The often-problematical drive system on this lathe has been cleverly modified to accept any motor - the one fitted being a powerful DC type with variable-speed drive. Pictures of the lathe for sale here and details of raglan lathes here For Sale: Myford ML7 Lathe 3.5" x 20" gap-bed, backgeared and screwcutting.Well equipped with: Burnerd Super-precision 5-inch adjustable 3-jaw chuck, Burnerd 6-inch 4-jaw chuck, Dixon quick-set toolpost with four holders (two standard, one boring and one parting-off), fixed steady, travelling steady, thread-dial indicator and the maker's handbook. Mounted on the maker's cabinet stand with chip tray and levelling blocks, this ML7 is in sound working order and complete with: extra-long T-slotted cross slide with a Super 7 feed screw, micrometer dial and handle, 3-jaw chuck, the correct half-depth body 6-inch Burnerd independent 4-jaw chuck, small 4-jaw chuck, fixed steady, a graduated handle to the leadscrew end, three angle plates, tailstock chuck, a set of screwcutting changewheels including some larger-than-usual examples, faceplate and catchplate. £550 Phone: 0788-0340400 or 01286-676914 (North Wales) Pictures of the Myford ML7 lathe for sale here and details of Myford ML7 lathes here I also have a Leinen LZ4P lathe and would appreciate contact with other owners For Sale: Naerok Vertical Milling and Co-Ordinate Drill Machine. R8 taper spindle (Bridgeport taper so lots of inexpensive tooling available) that has both fine feed by worm-and-wheel gearing and a rapid-action drilling handle.In excellent working order and ready for immediate use. Unlike other similar machines by Warco and Whitecote, etc., the Naerok's head's travel for coarse settings is by a bevel box at the base of the column - this keeping the head in alignment as it is raised and lowered. 1-phase motor with drive by an "A" section V-belt to an intermediate, self-aligning, 3-step jockey pulley and then to a 4-step front pulley - the arrangement giving 12 speeds that spans approximately 100 to 2000 r.p.m.fitted with both fine and quick-action drilling feeds - both along the axis of feed.I have owned the miller for ten years in which time it has seen little use.

Leave a Reply